About Pro Gravel Calculator
Pro Gravel Calculator is an independent, free estimating tool for gravel, sand and stone. It turns three measurements — area, depth and material — into the volume, weight and bag count you need before ordering.
What the calculator does
The calculator supports rectangular, circular and L-shaped areas in imperial or metric units. Imperial results show volume in cubic yards, weight in short tons and the number of 50 lb bags. Metric results show volume in cubic metres, weight in metric tonnes and kilograms, and the number of 25 kg bags. Each result also displays the equivalent in the other unit system. Every result is an estimate for planning; it is not a substitute for a site survey or a supplier's own quantity calculation.
The site is not a quarry, contractor or materials marketplace. We do not sell aggregate and we do not earn a commission from the suppliers you contact.
How the estimate is calculated
The estimate converts every dimension to feet, calculates volume, then multiplies by the material's loose bulk density; waste and compaction are applied last.
- Convert every dimension to feet. Feet and inches are added together as
feet + inches ÷ 12. Metres and centimetres are converted to feet using the exact factor 0.3048 m per foot. - Calculate the area. Rectangle: length × width. Circle: π × radius². L-shape: Section A + Section B.
- Convert depth to feet. Inches are divided by 12. The metric slider label shows the same depth in millimetres or centimetres.
- Calculate volume.
cubic yards = area (ft²) × depth (ft) ÷ 27. Metric volume iscubic metres = cubic yards × 0.764554857984. - Estimate weight.
short tons = cubic yards × 27 × density (lb/ft³) ÷ 2,000. Metric weight iskilograms = pounds × 0.45359237andmetric tonnes = kilograms ÷ 1,000. - Estimate bags. Imperial uses total pounds ÷ 50; metric uses total kilograms ÷ 25. Both are rounded up to the next whole bag.
- Apply allowances. Waste (0–25%) and compaction (0–20%) are independent, user-controlled multipliers:
adjusted volume = base volume × (1 + waste ÷ 100) × (1 + compaction ÷ 100).
Density values used
The calculator uses 105 lb/ft³ for pea gravel, 100 lb/ft³ for crushed stone, 110 lb/ft³ for sand and 108 lb/ft³ for river rock as typical loose bulk densities. Weight depends on the material and on how loose or compacted it is:
| Material | lb/ft³ | lb/yd³ | Short tons/yd³ | kg/m³ | Metric tonnes/m³ |
|---|---|---|---|---|---|
| Pea gravel | 105 | 2,835 | ≈ 1.42 | 1,682 | ≈ 1.68 |
| Crushed stone | 100 | 2,700 | ≈ 1.35 | 1,602 | ≈ 1.60 |
| Sand | 110 | 2,970 | ≈ 1.49 | 1,762 | ≈ 1.76 |
| River rock | 108 | 2,916 | ≈ 1.46 | 1,730 | ≈ 1.73 |
Why you may see 2,835 lb/yd³ for crushed stone
The 2,835 lb/yd³ figure is a legitimate reference point: it is 105 lb/ft³, a density often quoted for compacted or higher-specific-gravity crushed stone. This calculator deliberately uses 100 lb/ft³ (2,700 lb/yd³) for crushed stone because that is a more typical loose bulk density for the material most suppliers deliver.
The difference is about 5%. For a 10-ton order that is roughly half a ton, which matters at the scale of a driveway. If your supplier publishes a test density or a weight per cubic yard, use their number instead of our default. The calculator is a planning aid, not a laboratory result for your specific pile.
Allowances, rounding and limits
- Waste and compaction are explicit allowances. Both sliders default to 0%, so the base result is the geometric volume. Set waste to about 10% for typical projects and up to 15% for loose rounded stone, sloped sites or a soft subgrade. Compaction is applied independently after waste:
base × (1 + waste ÷ 100) × (1 + compaction ÷ 100). - Two-decimal display. Volume and weight are rounded for readability. Bags are rounded up so you do not see a fractional bag. Metric results show the same estimate in m³, metric tonnes, kilograms and 25 kg bags.
- Compaction changes volume. Gravel is usually sold loose but compacted in place. A 4-inch loose layer can finish thinner after compaction; plan lifts and depths accordingly. The driveway preset uses 12%, the midpoint of the usual 10–15% range.
- Moisture changes weight. Wet sand and gravel weigh more than dry material. Suppliers price by weight or volume; confirm which unit their quote uses.
- Shape assumptions. The L-shape mode adds two rectangles. It does not account for curves, cut-outs, retaining walls or over-excavation.
Sources and references
Density values are typical planning figures compiled from published aggregate supplier data and standard estimating references. They are presented as ranges in practice, not as universal constants. Our cost guides use the published U.S. price data described on those pages, including:
- GoodGravel, Gravel Prices by State (October 2026 edition) — median and middle-half prices from 10,101 published listings across 522 U.S. supply yards.
- U.S. Geological Survey, Crushed Stone Statistics and Information — background on crushed stone production and use.
Where a figure is an illustrative planning example rather than a published measurement, the page says so. We do not present invented customer bills, review counts or search data as facts.
Corrections and editorial standards
If you find an error, a broken source or a density that does not match your supplier's data, please contact us with the page and the evidence. Corrections are reviewed against the source before publication. Commercial relationships do not determine which materials or methods we recommend.
The calculator and guides are written for a U.S. audience, with metric inputs and outputs for international visitors. Local codes, quarry specifications and site conditions always take precedence over a general guide.
Ready to estimate? Open the free gravel calculator, or read the gravel type comparison before you choose a material.